![]() Hopefully some of our professional repair technicians can chime in and confirm or deny my diagnosis this is just my opinion, but I have worked on a lot of circuit boards in my career and that's what it looks like to me. It's got a lot of pins on both sides of the connector, so this is a case where it's going to be best to leave it to a professional. That's about the only remedy you've got for fixing this yourself unless you've got pretty good SMD soldering skills, because if that doesn't work you're going to have to replace the connector. I'm betting that's the issue for most of your games for some reason your Rayman Legends game doesn't seem to need that pin to work, while the other games all do. We highly recommend professional repair to ensure this part is correctly installed and restore your all. If your device can not transfer data, this is the part you need and each item has been checked and in good condition before shipping. It may help to remove the foam pad before reinstalling the card reader. Carefully re-read the second bullet item on Step 10: During reassembly, make sure the press connector underneath the foam pad is firmly connected to the motherboard. You just need to get it bent up far enough that the flex cable goes under it if you bend it up too far it won't make contact and you'll be in the same boat with that one pin not making contact. Replace your non-working or faulty Micro SD Card Slot Reader Port. It sounds like you don't have a good connection between the SD card reader and the motherboard. It looks to me like one of the pins is bent down too far and is going under the flex cable rather than on top of it like it should. With a pair of fine tip tweezers, magnifying glass and a bright light, you'll want to see if you can straighten that pin. ![]() The gap there is not normal, and when combined with the apparent damage to the flex cable, it's a fairly safe bet you've got a bent pin in there. I need any suggestions even the bizzare one's cuz i do not have any pro material like hot soldering.Yeah, that connector on the motherboard is definitely suspicious. The entire process takes about 5 minutes to complete.more. Im on 8.1.0 ofw with atmosphere 8.x.x and hekate 4.10.x. 1K Share 76K views 3 years ago This video shows you how to replace the micro SD reader on a Nintendo Switch. iFixit's Phillips bits are designed to be cross-compatible with JIS-style screws. The Switch uses JIS screws, but you can use a Phillips screwdriver in a pinch. In hekate a message in red appear and advice you to : Follow this guide to replace a damaged or faulty microSD card reader on your Nintendo Switch game console. I do not have the pro materials for this ,so i was thinking of much of solutions and you tell me !ġ- replace the motherboard ! it need 70€, is the mother board patchable ,idk !?Ģ- can i use a nintendo switch without a mSD card (just usb perhaps) ,idk !?ģ-the conector reader in the mother board is conected with biggers one's ( yellow rectangle) : can i wire those points and make my own mSDreader, i dont mind put the switch in a horrible estetic way if i manage to get it workingģa- if this solution above is doable ,what pin/point of the mother board GO where in the micro sd card ?Ĥ- do i just glue a 1mm wire (i have it) in the place of the missing pin ?ĥ- what this pin do/transfer ? because the switch do not reconize the sd card without. Removing the backplate and simply making sure the ribbon cable is plugged all the way in would be an easy thing to check. In the process of swapping their backplates they found the readers had disconnected entirely with little to no force. I can manage numerous things but this is a tiny soldering or i can use glue, the problem is 4.99 + 5.95 shipping Sold by: Ambertown Have one to sell Micro SD TF Card Slot Socket Reader Board for Nintendo Switch NS NX Console Replacement Brand: Ambertown 4. There has been more then a few users whose SD card readers were only lightly plugged in. There is a pin from the mother board mSD card reader who is not there, it's really small like 1mm. In this video I've made a guide of replacing a faulty game card reader on the Nintendo switch. ![]() If your battery is swollen, take appropriate precautions. This reduces the risk of fire if the battery is accidentally damaged during the repair. ![]() For your safety, discharge the battery below 25 before disassembling your Switch. 2: Remove the screw below the SD card and a screw from the bottom of the system next to the USB C port. Maybe clean the reader while youre in there. Here are the steps: 1: Shut down the system and remove the SD card and kickstand. I was having problems with my Microsd card not reconized from 2 month's now, so i just buy a scredriver and open it and what i saw freeze my blood : ( Use this guide to replace the game card reader daughterboard in your Nintendo Switch OLED. If that is the case, follow the steps below. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |